Hi, guys!
New firmware mod for Git G3 has been created. Image processing settings have been adjusted, bitrates doubled and new video resolutions (1080p50, 1080p48) added.
UPDATE (2019-02-06): Fixed issues with default sensor mode added in previous version, adjusted AE and noise reduction settings, better image quality.
Check detailed list of changes:
UPDATE (2019-02-22): Additional fix for custom sensor mode, updated color correction, reworked Low Light feature to reduce motion blur (Off) or reduce noise/increase brightness (On) for 30/60fps.
UPDATE (2019-03-09): Resolved frame sync issue for 1080p60 by switching to 59.94fps and updated autoexposition and color correction settings. Introduced "mod of mod" with settings for EIS of 170° FOV version of camera.
UPDATE (2019-03-30): Added ISO Limit feature, 1080p25/1440p25 video resolutions and updated settings for AWB and Noise Reduction.
UPDATE (2019-04-21): Fixed issue with broken EIS for 1080p60
Make sure, that official firmware v2.2 is installed on the camera before installing this mod.
Please note, that it is based on firmware for "no distortion" 90° FOV version of camera,but might be working properly with 170° FOV version, although it has not been tested yet. but it works fine with 170° FOV version, as it was confirmed by several testers.
UPDATE (2019-04-21): Modified firmware could be downloaded here
Please leave your feedback and comments!
New firmware mod for Git G3 has been created. Image processing settings have been adjusted, bitrates doubled and new video resolutions (1080p50, 1080p48) added.
UPDATE (2019-02-06): Fixed issues with default sensor mode added in previous version, adjusted AE and noise reduction settings, better image quality.
Check detailed list of changes:
UPDATE (2019-02-22): Additional fix for custom sensor mode, updated color correction, reworked Low Light feature to reduce motion blur (Off) or reduce noise/increase brightness (On) for 30/60fps.
UPDATE (2019-03-09): Resolved frame sync issue for 1080p60 by switching to 59.94fps and updated autoexposition and color correction settings. Introduced "mod of mod" with settings for EIS of 170° FOV version of camera.
UPDATE (2019-03-30): Added ISO Limit feature, 1080p25/1440p25 video resolutions and updated settings for AWB and Noise Reduction.
UPDATE (2019-04-21): Fixed issue with broken EIS for 1080p60
Git G3 Duo 90 firmware mod (based on official v2.2)
2019-04-21
1. Fix issue with broken EIS for 60fps modes.
2. AE and AWB settings adjusted.
3. Changed Effect Sepia to convert from full range to limited range (same as Black&White) with increased saturation.
2019-03-30
1. Added ISO Limit feature: setting ISO with Shutter Speed Auto will prevent ISO rising higher than specified value, except for ISO 50 - max ISO 6400 will be used.
2. Video resolution WVGA replaced with 1080p25 and 1440p25 for High bitrate.
3. Noise reduction parameters tunning.
4. Updated video resolutions for WiFi enabled mode to match new resolutions (1080p50, 1080p48, 1080p25, 1620p30)
5. AWB settings updated.
2019-03-08
1. Changed video framerate for 1080p60 from 60fps to 59.94fps to resolve sensor sync issue.
2. Updated color correction settings.
3. Automatic exposure settings adjusted.
2019-02-22
1. Another fix for new sensor mode used for 1080p30/1080p48/1440p.
2. Updated color correction settings.
3. Feature "Low Light" is enabled again with following functionality: Low Light On - lowest shutter speed set to 1/30s for 30fps, 1/60s for 60fps (50Hz, will cause flickering with some light sources); Low light Off - 1/50s for 30fps(50Hz), 1/60s for 30fps(60Hz), 1/100s for 60fps (50Hz), 1/60s for 50fps and 60fps(60Hz).
2019-02-06
1. Fixes for ISO50/ISO100 issues in new sensor mode used for 1080p30/1080p48/1440p.
2. Tuned noise reduction settings to improve image details and reduce noise level in low light.
3. Changed sensor timings for 1620p30 and 2160p24 modes to avoid frame doubling/skipping.
4. Added missing support for VGA 240fps video resolution.
5. Adjusted parameters for AE for all modes in order to improve highlights in bright light and avoid frame doubling in low light (720p120/VGA240).
6. Lowered compression level for .jpg photos for better image quality.
2019-01-19
1. Sharpness settings changed: Strong - same as original Normal; Normal - external edges disabled; Soft - sharpening disabled.
2. Changed params for Auto WB.
3. AE params and gamma curve for Normal contrast adjusted.
4. Color correction changes.
5. Changed sensor timings from 29.97fps to 30fps, 59.94fps to 60fps to match recorded video framerate and avoid frame doubling/skipping.
6. Doubled bitrates for video (Low: ~32mbps, Med: ~52mbps, High: ~70mbps). Make sure your sd card is fast enough.
7. Adjusted settings for noise reduction filters.
8. Image effect "Black and White" has been changed to adjust video luma component to limited range.
9. Replaced 1440x1080x60 (1080p60 4:3) video resolution with 1920x1080x48 (1080p48)
10. Replaced 1296p30 video resolution with 1920x1080x50 (1080p50)
11. Replaced 2160p24 (16:9) video resolution with 2880x1620x30 (1620p30)
12. Changed sensor mode for 1440p30 and 1080p30 video resolutions.
2019-04-21
1. Fix issue with broken EIS for 60fps modes.
2. AE and AWB settings adjusted.
3. Changed Effect Sepia to convert from full range to limited range (same as Black&White) with increased saturation.
2019-03-30
1. Added ISO Limit feature: setting ISO with Shutter Speed Auto will prevent ISO rising higher than specified value, except for ISO 50 - max ISO 6400 will be used.
2. Video resolution WVGA replaced with 1080p25 and 1440p25 for High bitrate.
3. Noise reduction parameters tunning.
4. Updated video resolutions for WiFi enabled mode to match new resolutions (1080p50, 1080p48, 1080p25, 1620p30)
5. AWB settings updated.
2019-03-08
1. Changed video framerate for 1080p60 from 60fps to 59.94fps to resolve sensor sync issue.
2. Updated color correction settings.
3. Automatic exposure settings adjusted.
2019-02-22
1. Another fix for new sensor mode used for 1080p30/1080p48/1440p.
2. Updated color correction settings.
3. Feature "Low Light" is enabled again with following functionality: Low Light On - lowest shutter speed set to 1/30s for 30fps, 1/60s for 60fps (50Hz, will cause flickering with some light sources); Low light Off - 1/50s for 30fps(50Hz), 1/60s for 30fps(60Hz), 1/100s for 60fps (50Hz), 1/60s for 50fps and 60fps(60Hz).
2019-02-06
1. Fixes for ISO50/ISO100 issues in new sensor mode used for 1080p30/1080p48/1440p.
2. Tuned noise reduction settings to improve image details and reduce noise level in low light.
3. Changed sensor timings for 1620p30 and 2160p24 modes to avoid frame doubling/skipping.
4. Added missing support for VGA 240fps video resolution.
5. Adjusted parameters for AE for all modes in order to improve highlights in bright light and avoid frame doubling in low light (720p120/VGA240).
6. Lowered compression level for .jpg photos for better image quality.
2019-01-19
1. Sharpness settings changed: Strong - same as original Normal; Normal - external edges disabled; Soft - sharpening disabled.
2. Changed params for Auto WB.
3. AE params and gamma curve for Normal contrast adjusted.
4. Color correction changes.
5. Changed sensor timings from 29.97fps to 30fps, 59.94fps to 60fps to match recorded video framerate and avoid frame doubling/skipping.
6. Doubled bitrates for video (Low: ~32mbps, Med: ~52mbps, High: ~70mbps). Make sure your sd card is fast enough.
7. Adjusted settings for noise reduction filters.
8. Image effect "Black and White" has been changed to adjust video luma component to limited range.
9. Replaced 1440x1080x60 (1080p60 4:3) video resolution with 1920x1080x48 (1080p48)
10. Replaced 1296p30 video resolution with 1920x1080x50 (1080p50)
11. Replaced 2160p24 (16:9) video resolution with 2880x1620x30 (1620p30)
12. Changed sensor mode for 1440p30 and 1080p30 video resolutions.
Make sure, that official firmware v2.2 is installed on the camera before installing this mod.
Please note, that it is based on firmware for "no distortion" 90° FOV version of camera,
UPDATE (2019-04-21): Modified firmware could be downloaded here
Please leave your feedback and comments!
Last edited: