Viofo RNF210 Camera Clicking

clevoir

New Member
Joined
Dec 3, 2024
Messages
21
Reaction score
3
Location
Brentwood
Country
United Kingdom
I have been using a Viofo A229 Pro with rear camera for about year with no problems

I've just added a RNF210 internal camera, and after about an hour the camera starts to click randomly. If I disconnect the camera, it reverts to 2 channel recording, and the clicking stops, so it's definitely the interior camera making the noise. Camera is connected to dascam using the 0.3m Viofo lead.

When the clicking is happening, the camera stays in 3 channel mode, and I assume that the clicking is the IR LED's being switched on and off?

I haven't seen the problem in short daylight trips, but today was the first time that the camera has been used for over an hour. 1st trip was in 100% darkness and 2nd trip in daylight.

In the camera settings I have IR LED's set as auto, I now set them as on and will try some more trips tomorrow. But I ideally don't want to leave IR on all the time as this will cause unnecessary current draw and reduce the amount of time that parking recording will operate for.

I've noticed the camera gets very warm, does this sound like the camera is faulty?
 
I appreciate that the clicking could be a IR cutoff filter too, but why after a hour? And why in journey in 100% darkness and another journey in daylight?
 
The click sound will be the mechanical IR cut filter being moved in/out between the lens and the sensor. The decision to engage that and the IR LEDs should be the ambient light level.

Is the interior camera placed near the back of the rear view mirror, such that the camera may be confused by IR light being reflected back to the camera? A bit like how motion sensor lights in people's porch can sometimes set themselves off repeatedly.
 
The interior camera is mounted the rear view mirror, fixed to the overhead console. I've seen test interior cameras in this location in testing carried out by other users. I can appreciate that the filter might click once or twice due to ambient light levels, but camera will click multiple times.
 
Sorry, fat fingers. Camera is mounted beneath the rear view mirror and is fixed to overhead console
 
Mounted like this, (this is somebody else's' photo)

1762207807851.webp
 
The interior camera is mounted the rear view mirror, fixed to the overhead console. I've seen test interior cameras in this location in testing carried out by other users. I can appreciate that the filter might click once or twice due to ambient light levels, but camera will click multiple times.
There will be a click when the IR LED is turned on/off. If you turn on IR instead of Auto, do you still hear click sound multiple times?
 
I've tried today with IR turned on with no problems in 2 one hour journeys. I hear a click when IR is switched on or off. But on an hour journey with IR set to auto I heard the IR clicking multiple times say after 50 minutes. I drive 1 hour to work as it's getting light and 1 hour home as it's getting dark. I would expect a single click as the IR is being switched on off due to changes in lighting level. I've set IR back to auto and will see what happens tomorrow.
 
on an hour journey with IR set to auto I heard the IR clicking multiple times say after 50 minutes. I drive 1 hour to work as it's getting light and 1 hour home as it's getting dark. I would expect a single click as the IR is being switched on off due to changes in lighting level.
It sounds like the camera is switching between modes when the ambient light level is close to the threshold - they light level varies as you change direction, go under trees, pass streetlights etc.

Have you watched any footage to confirm what the dashcam is doing?
 
In this morning's 1 hour trip, I set off in darkness and after 20 mins joined well lit roads. The camera was silent for 20 mins, but after that the IR cut filter kept randomly turning on and off. Footage shows the camera keep switching between black&white / colour. I drove thorough a well lit tunnel, which increased the rate that the filter was being switched on & off. It did not start to get light until after 40 mins, and I couldn't match the filter being turned on / off to any events.

I drove home in daylight and the camera stayed silent except 2 occasions where I drove under trees where the light level dropped.

In my car (Golf Mk8) the overhead console is illuminated when the headlights are on. The camera is mounted below these lights, but looking at the footage I can see part of these illuminated "squares" are in camera view.

I wonder if the illumination from these is causing the camera to be confused? I have now lowered the camera view so that they are out of shot, and I'll trial again.

I noticed where driving under trees, there does not appear to be any latency in switching the filter on and off. But simply on as light level drops and then off when the light level increased? In the algorithm to operate the IR I would have though that there would have been latency / delay to avoid the rapid operation of filter?

1762360348035.webp


1762360383986.webp
 
I noticed where driving under trees, there does not appear to be any latency in switching the filter on and off. But simply on as light level drops and then off when the light level increased? In the algorithm to operate the IR I would have though that there would have been latency / delay to avoid the rapid operation of filter?
It's a double edged sword. If you drive into a tunnel or car park you might want the camera to react quickly. But I agree that for normal driving some sort of averaging the light levels or delay on switching would be good.
 
Oh well reaming the camera made no difference! I've made a number of trips now, in total darkness the camera is silent but as soon as you move on to well lit roads the camera will randomly click and switch between B&W/ colour. Similarly driving at dusk time, the camera will randomly click too. It seems that at a certainly lighting level(s), the camera will "hunt" not knowing what to do and there is no latency or buffering. It's a disappointing design to be honest.
 
Is there any packaging material left on the sensor?
 
All packaging has been removed from the camera, and I am seeing good quality images. The images of me in the car in the post above are of a cropped photo taken of a tablet connected to the camera, so are not representative of the true image.
 
@clevoir going by your photo above check to see if the camera switches when car headlights are behind you.
You back window is very clear which is great to see what's behind but not so great for a sensor that looks directly there to.

Point the sensor down so the camera only catches part of the roof lining that might reduce the light level enough for the sensor not to activate so often.
 
@clevoir Here is the location of the sensor.
Reducing the light that enters this will alter the sensitivity of the sensor. Eg a piece of paper.

@viofo another memu option to monitor and adjust the light input. 🤯
Hows the professional sub menu coming along? The only set once items and the more complicated features that generally only advanced users and installers will use.



IMG_2119.webp
 
In this morning's 1 hour trip, I set off in darkness and after 20 mins joined well lit roads. The camera was silent for 20 mins, but after that the IR cut filter kept randomly turning on and off. Footage shows the camera keep switching between black&white / colour. I drove thorough a well lit tunnel, which increased the rate that the filter was being switched on & off. It did not start to get light until after 40 mins, and I couldn't match the filter being turned on / off to any events.

I drove home in daylight and the camera stayed silent except 2 occasions where I drove under trees where the light level dropped.

In my car (Golf Mk8) the overhead console is illuminated when the headlights are on. The camera is mounted below these lights, but looking at the footage I can see part of these illuminated "squares" are in camera view.

I wonder if the illumination from these is causing the camera to be confused? I have now lowered the camera view so that they are out of shot, and I'll trial again.

I noticed where driving under trees, there does not appear to be any latency in switching the filter on and off. But simply on as light level drops and then off when the light level increased? In the algorithm to operate the IR I would have though that there would have been latency / delay to avoid the rapid operation of filter?

View attachment 87584

View attachment 87585
If you adjust your camera lens so it points downward, which reduces the ceiling view, you'll eliminate light bursts and avoid sudden filter changes.

For example, you can try adjusting the upper part of the video frame so that it aligns with the rear seat lighting buttons.

Please try it and let me know.
 
I have lowered the camera as far as a can without losing view of the rear window

Yes I get switching when car lights are behind me, but only on well lit roads. However it is random as I can drive with headlights behind me with the camera not switching and remaining in black and white

I appreciate that I can cover the sensor, but this is just masking the fact that the camera is not functioning correctly.

1763046539575.webp
 
Refreshing this thread.
I currently have the RNF210 mounted on the windscreen, above the mirror on the driver’s side. This works, but it’s not ideal:

1) a small part of the headliner is visible in the frame
2) when the sun visor is in use, it partially blocks the image

Does anyone have a clever idea for mounting it to the headliner without damaging it too much?
I tried using neodymium magnets placed between the steel roof and the headliner, but that didn’t work - the magnetic force was too weak.
From my testing, mounting it centrally on the headliner, slightly in front of the mirror, seems to be the most optimal position.
(What’s worse, there may be additional vibrations, whereas when mounted on the windscreen this issue is completely eliminated.)
 
Refreshing this thread.
I currently have the RNF210 mounted on the windscreen, above the mirror on the driver’s side. This works, but it’s not ideal:

1) a small part of the headliner is visible in the frame
2) when the sun visor is in use, it partially blocks the image

Does anyone have a clever idea for mounting it to the headliner without damaging it too much?
I tried using neodymium magnets placed between the steel roof and the headliner, but that didn’t work - the magnetic force was too weak.
From my testing, mounting it centrally on the headliner, slightly in front of the mirror, seems to be the most optimal position.
(What’s worse, there may be additional vibrations, whereas when mounted on the windscreen this issue is completely eliminated.)
Maybe you can build something like this that will fit to the front of the headliner?

 
Back
Top