DVR won’t turn off

Louisloong

New Member
Joined
Feb 4, 2018
Messages
28
Reaction score
4
Country
Australia
After riding a few hours and when I turned the bike off, I looked at my phone WiFi and noticed that I was still connected to the Innovv K2 .
I checked the DVR and it was hot. It stayed on until I pulled out thr fuse. Faulty DVR ?
 

OCD Tronic

Well-Known Member
Retailer
Joined
Nov 5, 2016
Messages
966
Reaction score
697
Location
Carson City, Nevada (USA)
Country
United States
Dash Cam
VIOFO, GitUp, INNOVV, QVIA, GUARD TRAK + More on Amazon.com
Do you having parking mode enabled in the app? If so it will remain on.
 
OP
L

Louisloong

New Member
Joined
Feb 4, 2018
Messages
28
Reaction score
4
Country
Australia
Been using it for a few months without problem. Suspect there’s some fault in the power module. Only does it when it’s hot.
It was fine when tested with the bike on and off. Not fine after a long day ride.
 

OCD Tronic

Well-Known Member
Retailer
Joined
Nov 5, 2016
Messages
966
Reaction score
697
Location
Carson City, Nevada (USA)
Country
United States
Dash Cam
VIOFO, GitUp, INNOVV, QVIA, GUARD TRAK + More on Amazon.com
Where are you located? Who was your seller? They should be able to provide support if you’re stuck.
 

niko

Well-Known Member
Retailer
Joined
May 1, 2013
Messages
10,532
Reaction score
6,408
Location
Dublin
Country
Ireland
Dash Cam
Street Guardian UK / EU / EEA Distributor
What FW version?

Sent from my VKY-L29 using Tapatalk
 

OCD Tronic

Well-Known Member
Retailer
Joined
Nov 5, 2016
Messages
966
Reaction score
697
Location
Carson City, Nevada (USA)
Country
United States
Dash Cam
VIOFO, GitUp, INNOVV, QVIA, GUARD TRAK + More on Amazon.com
I asked the factory.

They said:

“That happens when two cameras don’t connect to dvr well Or the front camera has connection issue. Remove the camera which plugged into the port where has F printed beside and plug other camera to this port only, and then check if has issues”
 
OP
L

Louisloong

New Member
Joined
Feb 4, 2018
Messages
28
Reaction score
4
Country
Australia
I asked the factory.

They said:

“That happens when two cameras don’t connect to dvr well Or the front camera has connection issue. Remove the camera which plugged into the port where has F printed beside and plug other camera to this port only, and then check if has issues”
Positively sure all connections are perfect. The DVR only would not turn off when it has been on for a few hours. It gets really really hot too. On short rides, I don’t have a problem.
 

OCD Tronic

Well-Known Member
Retailer
Joined
Nov 5, 2016
Messages
966
Reaction score
697
Location
Carson City, Nevada (USA)
Country
United States
Dash Cam
VIOFO, GitUp, INNOVV, QVIA, GUARD TRAK + More on Amazon.com
Inspect complete length of wires for pinched cables.
 
OP
L

Louisloong

New Member
Joined
Feb 4, 2018
Messages
28
Reaction score
4
Country
Australia
My solution at last.
Opened up the DVR. Drilled some holes on the back metal case. Stuck a small 30mm fan. Drilled a few more holes for air in. Fan sucks the air out.
Connected fan to switched 12V. When DVR starts, fan starts. No problem after that.
 

Tracer

New Member
Joined
Sep 11, 2018
Messages
8
Reaction score
1
Country
Canada
Yeah, I thought that sounded like they had a heat problem like my K1 did, among other fatal problems it had.
 
Top