Search results

The first is the main thing - the hybrid's electrical circuit works in its own way, keep this in mind when you connect a Hardwire Kit for the dashcam to work in parking mode. Everything else is unchanged. The second is cable losses. The losses on the 5 volt line are much greater than on the 12...

Yes, I would really like to be able to switch, in the case of only two cameras, to a higher bitrate of the front camera. Moreover, the N4 Pro with three cameras already has a bitrate of 32.4 Mbps (versus 14.3 Mbps on the N5). I think @Jeff_Vantrue and a team of engineers are monitoring the...

So what - I had to ask for help from comrades in the forum. Many thanks for the help @Karagandinez and @vvs49!!! They sent a dump, with the help of which, as well as the CH341A programmer, it was possible to restore the rear camera. Hooray!!! (y) :) We made it! PS: Here is the firmware...

To be clarified: after several verification tests confirmed: load disconnection at 11.69 Volt, after 4:45-4:57 min (Vantrue made with a margin :) ) And one more thing: the load is activated (power supply to the dashcam) occurs when the voltage rises to 12.00 Volts.

Is the remote control panel connected? In some models of the BlueSkySea, the Wi-Fi module was in the remote control

I tested this kit a bit, here are the first results: First and foremost, the adapter can withstand the load with a margin. During testing, the maximum load was 2.6A, with a further increase, the adapter turns off - it goes into protection. The voltage for powering the dashcam on the Type-C...

It is forbidden to use fuses that protect the circuits of engine control systems, as well as systems that affect traffic safety - steering, brakes, etc. PS: There are many other connection circuits - different lamps, cigarette lighter socket, trailer wires and others. And before connecting...

Yes, Solomon's decision. But you need to keep in mind the connection method - if both dashcams are connected to the rear fuse box, then this kit will be enough, and if the front recorder is connected to the front fuse box, then it may not be enough. Although, it's probably better to extend the...

No, it's just that in the diagram for connecting a BMW CarEye dashcam it is indicated so. We can find the fuses that protect the Bat+ (line 30) and ACC (line 15) circuits. But online it is somewhat more difficult. :)

With absolute certainty, we can say that one of the fuses is F273, which protects the cigarette lighter socket circuit. In the first video I linked to, they also connected to this fuse. You just need to check - there is a constant +12 or ACC, depending on this, and determine the second...

Hello, Recommended Viofo memory cards here: https://support.viofo.com/support/solutions/articles/19000133471-what-memory-card-is-recommended-for-a-viofo-dashcam- (easily found by searching the web) For extension, copper stranded wires with a cross section of 18 AWG / 0.75 mm2 (millimeters...

Yes, there is such a problem, dealers do not want to get involved, and stores are incompetent in such things. Okay, let's try. Can you take a photo of the fuse blocks you plan to connect to to see what fuses are actually used in your car?

The yellow ACC wire must be connected to the contact where the +12 Volts appears when the ignition is turned on.

This happens when the battery inside the dashcam no longer holds a charge and needs to be replaced. In this case, the battery voltage is not enough to complete the file when the external power is turned off, and it will work until the battery finally runs out. When external power is connected...

How can I identify the international version and where can I buy it? The product page shows the restrictions in which countries this kit can be used, and there are no such restrictions in the international version?

Yes, for example, 70mai has a 4G Hardwire Kit UP04 for X200 Omni is impressive, a very interesting solution, perhaps Vantrue plans to move in a similar direction, we'll see. But what else I would like to pay attention to is a relic of three wires. Look at the picture under the spoiler, I would...

I uploaded a new firmware N5_VT-ECF211, but as before, on the updated firmware, the front cabin cam goes into a purple-pink color. When I turn ON the IR LED, the picture switches to black and white. Other cameras work correctly. I can try and ride with this mode, but infrared diodes will...

There is already a change log, added to message #16

You've already seen this from Viofo? -> https://viofo.com/blog/how-to-switch-a139-dash-camera-to-wi-fi-station-mode-with-app-b76.html

BlackVue dashcams also use a SIM card, for example, you can see how they set up communication with the cloud and all the questions related to this, at least here: Have you looked at the instructions on the Vezo website Arvizon? Here...