@
Sunny, please use this firmware to update your nanoQ and have a try again.
the IQ in last firmware was adjusted to improve the night view but seems too much for day light.
3.29 log:
1, revise GPS STAMP on screen
2, correct SCREEN OFF DELAY
3, correct time zone setting -- please test
4, optimize IQ setting, reduce the exposure -- please test
5, correct HDR icon display
6, increase video bit rate to 16M and 20M, please test
16M bit rate version:
www.nanodashcamera.com/firmware/mar.29/mini0903-20160329-test16M.7z
20M bit rate version:
www.nanodashcamera.com/firmware/mar.29/mini0903-20160329-test20M.7z
guys please check if this exposure is ok for both day and night, and if the different bit rates works for you camera&card.
looking forward your feedback.
Thanks
Rayman
I have received the Mini 903 camera before several days ago. (Bought from Ebay, Estore009)
firmware:
I have upgraded it from mini0903-20160316
to
mini0903-20160329-test20M
1, revise GPS STAMP on screen - NOT RESOLVED (stamping is ON in the settings)
2, correct SCREEN OFF DELAY - RESOLVED
3, correct time zone setting -- please test - RESOLVED - It keeps the setting after the switch off/on
4, optimize IQ setting, reduce the exposure -- please test - NOT RESOLVED - exposure is too high at day time
5, correct HDR icon display - YES, there is
6, increase video bit rate to 16M and 20M, please test- (Not tested yet)
GPS issues: no lock, no stamping, no satellite symbol.
I had it in the FW mini0903-20160316, but not accurate location.
Part of the log (FW mini0903-20160316):
A,150416,151310.000,4606.1831,N,1939.9128,E,0.7,+0.61,+4.71,-0.06;
A,150416,151311.000,4606.1841,N,1939.9124,E,0.7,+0.96,+4.81,-0.04;
A,150416,151312.000,4606.1851,N,1939.9120,E,0.5,+0.67,+4.80,-0.25;
A,150416,151313.000,4606.1860,N,1939.9117,E,0.5,+0.49,+4.84,-0.65;
A,150416,151314.000,4606.1870,N,1939.9113,E,0.6,+0.26,+4.85,-0.48;
With this new FW I don`t have it at all.
Part of the Log (mini0903-20160329-test20M):
......
V,060180,2943.020,,,,,,+0.11,+4.84,+0.14;
V,060180,2944.020,,,,,,+0.33,+4.91,+0.38;
V,060180,2945.020,,,,,,+0.37,+4.99,+0.28;
V,060180,2946.020,,,,,,+0.41,+5.12,+0.03;
V,060180,2947.020,,,,,,+0.27,+4.96,-0.04;
V,060180,2948.020,,,,,,+0.44,+5.00,-0.08;
V,060180,2949.020,,,,,,+0.21,+4.99,+0.19;
V,060180,2950.020,,,,,,+0.32,+4.96,-0.16;
V,060180,2951.020,,,,,,+0.33,+4.91,-0.28;
V,060180,2952.020,,,,,,+0.25,+4.82,-0.43;
V,060180,2953.020,,,,,,+0.33,+5.01,-0.32;
........
Moreover the small square plastic clip to lock the mount into the camera is too small. It cannot lock the camera.
Any suggestion, solution, please?