hardwire

Hi all, been lurking around this forum for the last week or so since receiving a 512GW as a gift. I've been having a play with the device to figure out what the different settings do, test-fitted the front camera in a few different places, picked up a 512GWRC to go with it and am now eagerly...

Hello all, I've been wanting to get into the dash cam scene for a bit now and I've been doing my research and I have decided that I want an a129 and utilize parking mode. In order to do this I was thinking about getting the VicoVation Vico-Power Plus and set the cut off for 12.2V then splicing...

I am trying to hard wire the Cellink Neo (rated 9A, using 20A fuse) and had a couple questions. I am not an expert in electrical engineering so correct me if any of the stuff I stated below is wrong. I have tested all my fuse slots and I do not have any empty ones that are ACC, thus I have to...

I just installed a Blackvue DR750S-2ch into my car. I like the all the features but I'm not liking the video quality (coming from an A119 in my old car). The main reason I went with the DR750 was because of its G-Sensor/movement activated parking mode. As my car is electric, it doesn't have...

I've been running two A119V2 cameras ( front and back) and powering them through the 12V sockets in my car. All good, no issues. Today, I hardwired the front camera using a "Dash Cam Store" install kit (http://www.thedashcamstore.com/dashcam-installation-kit-5-volt-usb-plug-mini-fuse/). I...

Hi all, New to the forum and dash cams in general. Recently purchased two dash cams for my car, Ford Focus mk3 (2013). Currently have front and rear dash cams. Front camera is the Nextbase 512g, hardwired into passenger fuse box (fuse 85 - 7.5a fuse / hot on ignition). Rear dashcam, Nextbase...

I have a 2010 Volvo XC60, Blackvue DR470-2ch dashcam, and a MotoPark Multi Safer S hardwiring kit. The problem: my dashcam won't "turn off", i.e. will continue to record video files, even when my car is off, locked, and there is no motion to trigger parking mode. Multi Safer setup: I have the...

I have the add-a-circuit kit into the cigarette lighter fuse. It works because the things connected to the lighter work fine with the tap. But the camera doesn't get power. Camera does work and I got a new set of wires thinking it was the wires that went bad. Nope, still nothing. Also tried a...

I have two A118 (non-capacitor) cameras in my car - one will power up with a turn of the ignition key but the other won't. I've been powering them for the past year with a dual power port (cigarette lighter style) and wires dangling around in the cabin. I wanted to clean it up so I ordered two...

Hi guys! I am not new here but I upgrade my computer and forgot my password... so.. hello again! So.. I have the GS98C dash cam - http://www.szdome.com/product-detail-20.html now I noticed to the parking mode and I know you need a hardwire for this option (if you want to leave that option on...

Hi. I recently purchased a A118C, which I have been running successfully from the cigarette lighter in my 2011 Nissan Qashqai with the supplied USB cable. Meanwhile I ordered a hardwire kit from ebay, it's now come, and I took the car to a local fixer to hardwire it all in. The hardwire is run...

So in my previous vehicle (2015 Mustang GT) I had a Thinkware F750 dash cam and it was hardwired to the fuse panel. I sold that car and bought a new car (2017 Shelby GT350) and also bought a Thinkware F770. According to the owner's manual, the fuse panels are pretty much exactly the same in...

I am a newbie in this matter. I need help on how to hardwire Thinkware F770 and Cellink B V2. Previously, I had hardwired my dashcam and parking mode was working fine. But recording time was very limited because of my battery. So, I bought Cellink v2 battery. But the problem now is that I only...

I am a newbie in this matter. I need help on how to hardwire Thinkware F770 and Cellink V2. Previously, I had hardwired my dashcam and parking mode was working fine. But recording time was very limited because of my battery. So, I bought Cellink v2 battery. But the problem now is that I only...

I've been searching for a while and settled for the A118. Seems to get decent reviews and I like the discreteness. Question: I don't want to tie up the cigarette lighter nor have visible cords to a USB adapter. I have minimal electrical skills, but I think I can manage hard-wiring to a current...

I had an escort redline radar (stolen by tow truck driver :mad:), and it was hard wired to my sunroof wiring harness nicely hidden in my 2004 bmw 330ci. Yeah I know I should have removed it but it was 2 am and i was overtired.. I used this kit to wire from Amazon: Link here It powered on and...

There is another socket on this unit called '4 pin remote switch extension connector' in the manual. Has anyone worked out what this is actually for and used it? I was kind of hoping I might add a second camera (rear) to it instead of using an twin adapter in the supplied socket. Cheers! Andy

Hi all, First off, I know this topic has been covered over and over but I am really struggling to find out what I need to, most topics end up talking about fuse replacement/piggyback kits... So I was bought a Dash Cam (Amacam M-80) and hard wire kit for my birthday and want to install it. I am...

I have seen more than one posting in DCT (can't find them just now) where they stated, or at least implied, that a certain hard-wiring kit would work with certain dash cam models and actually listed some dash cam models that the particular kit in question was compatible with. I have also seen...

If I have my dash cam hardwired to the fusebox and connected via a Cellink, T-Power Plus or some other similar secondary battery UPS, should I still buy a Battery Discharge Prevention device, such as the Lukas LK-290, Power Magic Pro, or ("the Mercedes of BDPs") the Vico-Power Plus? I am not...